1. Define Maintenance
Maintenance is the act of keeping something in good condition by
checking or repairing it regularly. f
2. Define Repair.
Repair is the process of restoring something that is damaged or deteriorated or broken, to good condition.
3. Define Rehabilitation.
Rehabilitation is the process of returning a building or an area to its
previous good conditions.
4. What are the two facets of maintenance?
The two facets of maintenance are
� Prevention
� Repair
5. What are the causes of deterioration?
� Deterioration due to corrosion
� Environmental effects
� Poor quality material used
� Quality of supervision
� Design and construction flaws
6. Define physical inspection of damaged
structure.
Some of the use full in formation may be obtained from the physical
inspection of damaged structure, like nature of distress, type of distress,
extent damage and its classification etc, their causes preparing and
documenting the damages, collecting the samples for laboratory testing and
analysis, planning for in situ testing, special environmental effects which
have not been considered at the design stage and information on the loads
acting on the existing structure at the time of damage may be, obtained. To
stop further damages, preventive measure necessary may be planned which may
warrant urgent execution.
7. How deterioration occurs due to corrosion?
� Spalling of concrete cover
� Cracks parallel to the reinforcement
� Spalling at edges
� Swelling of concrete
� Dislocation
� Internal cracking and reduction in area of steel reinforcement.
8. What are the steps in selecting a repair procedure?
� Consider total cost
� Do repair job in time
� If defects are few & isolated repair on an individual basis.
Otherwise do in generalized
manner
� Ensure
the repair prevents further development of defects
� In case of lost strength, repairs should restore the strength
� If appearance is a problem, the number of applicable types of
repairs become limited & the repairs must be covered
� Repair works should not interface with facilities of the structure
� Take care in addition of section to a member and in restributing
live loads and other live load moments. After selecting a suitable method of
repairs, and after considering all the ramifications of its application, the
last step is to prepare plans & specification and proceed with the work.
9. Discuss about the environment effects
which leads to deterioration of concrete structure.
Micro-cracks present in the concrete are the sources of ingress of
moistures atmospheric carbon di-oxide into the concrete which attack
reinforcement and with various ingredients of concrete. In aggressive
environme4nt concrete structure will be severely reduces.
10. What is the effect of selecting poor quality material for
construction?
Quality of materials, to be used in construction, should be ensured by
means various tests as specified in the IS codes. Alkali-aggregate reaction and
sulphate attack results in early deterioration. Clayey materials in the fine
aggregates weaken the mortar aggregate bond and reduce the strength. Salinity
causes corrosion of reinforcing bars as well as deterioration of concrete.
11. How can we determine the cause for deterioration of concrete
structure?
� Inspect & observe the structure
� Observe in bad & good weather
� Compare with other constructions on the area or elsewhere & be
patient
� Study the problem & allow enough time to do the job
12. What are the factors to be considered by the designer at the
construction site.
� Minimum and maximum temperatures
� Temperature cycles
� Exposure to ultra violet radiation
� Amount of moisture
� Wet/dry cycles
� Presence of aggressive chemicals
13. What are the steps in repair aspect?
� finding the deterioration
� determining the cause
� evaluating the strength of existing building or structure
� evaluating the need of repair
� Selecting & implementing a repair procedure
14. Define the fixed percentage method of evaluating the strength of
existing structure.
It is to assume that all members which have lost less than some
predetermined % of their strength are still adequate and that all members which
have lost more than the strength are inadequate. It is usually from 15% onwards
higher values are applicable for piling % stiffness bearing plates etc.
15. Discuss about the design and construction errors leading to
deterioration of a structure.
Design of concrete structures governs the performance of concrete
structures. Well designed and detailed concrete structure will show less
deterioration in comparison with poorly designed and detailed concrete, in the
similar condition. The beam-column joints are particularly prone to defective
concrete, if detailing and placing of reinforcement is not done properly.
Inadequate concrete cover may lead to carbonation depth reaching up to the
reinforcement, thus, increasing the risk of corrosion of the reinforcement.
16. Discuss about the quality of supervision to be followed at a site.
Construction work should be carried out as per the laid down
specification. Adherence to specified water-cement ratio controls strength,
permeability durability of concrete. Insufficient vibration may result in
porous and honey combined concrete, whereas excess vibration may cause
segregation.
17. What are the possible
decisions that can be made after evaluating the strength of a structure?
� to permit deterioration to continue .
� to make measures to preserve the structure in its present
condition without strengthening
� to strengthen the construction
� if deterioration is exceptionally sever, to reconstruct or
possibly abandonit.
18. How can we evaluate the strength of existing structure by stress
analysis?
This method is to make detailed stress analysis of the structure, as it
stands including allowances for loss of section where it has occurred. This is
more difficult & expensive. Here also the first stop is to make preliminary
analysis by fixed percentage method and if it appears that major repairs will
be required, the strength is reevaluated based on detailed stress analysis,
considering all contributions to such strength.
19. Define the load test method of evaluating the strength of existing
structure.
Load tests may be required by the local building offered, but they
should only be performed where computation indicated that there is reasonable
margin of safety against collapse, lest the test bring the structure sown. Load
test show strengths much greater than computed strengths when performed on
actual structures. When performed on actual structures. In repair work every
little bit of strength is important.
20. What are the possible decisions after finding a structure to be
inadequate?
� if the appearance of the existing condition is
objectionable - repair now
� if appearance is not a problem then
� Put the condition under observation to check if it is dormant or
progressive.
� if dormant - no repair
� if progressive - check the feasibility & relative
economics of permitting deterioration to continue and performing a repair at
some later date & of making the repair right away
Maintenance and repair of structure manual solve answer pdf file
ReplyDelete